Category Archives: HVAC/R Equipment & Fans

Morris TWG840590, Direct Drive Furnace Blower Motor, 3/4 HP

Morris, TWG840590, Direct Drive Furnace Blower Motor, 3/4 HP, 208/230V, 1075/3 Speed Features: Ball bearings now standard Installs with all Standard 48 frame mounting brackets Standard shaft length, diameter, and flats Uses 370V Capacitors 2.5in Diameter Hub Rings included Drain holes with plugs in booth end plates Automatic thermal overload protector Standard 48 frame motor

Morris TWG840730, Condenser Fan Motor, 1/2 HP, 208/230V, 1075/1 Speed

Features: Ball bearings now standard Installs with all Standard 48 frame mounting brackets Standard shaft length, diameter, and flats Drain holes with plugs in booth end plates Automatic thermal overload protector Standard 48 frame motor casing size Lower Power Consumption 60deg C Ambient design Electrically reversible Continuous Air Over Class B Insulation Quiet Operation Extended

Morris TWS-1, Wet Switch Flood Detector

Features: A solid state control designed to help prevent flooding, damage to carpets, walls, furniture, ceilins, etc. Built in test and reset button for eaiser installation Turns sytem off when detecing moisture due to condensate or drain leaks, One or two drops willcause Wet switch to turn off a unit, alerting a serviceman to a

Morris THDR-101, Sequencer – Blower Motor 1 Circuit, Delay On

Morris, THDR-101, Sequencer – Blower Motor 1 Circuit, Delay On – 1-24 sec, Off – 45-75 sec, SPST NO Features: Sequencers are used in electric heat systems to stage blower motors and heating elements 24 volt

Morris TWG840585, Direct Drive Furnace Blower Motor, 1/3 HP

Morris, TWG840585, Direct Drive Furnace Blower Motor, 1/3 HP, 115V, 1075/3 Speed Features: Ball bearings now standard Installs with all Standard 48 frame mounting brackets Standard shaft length, diameter, and flats Uses 370V Capacitors 2.5in Diameter Hub Rings included Drain holes with plugs in booth end plates Automatic thermal overload protector Standard 48 frame motor

Morris THDR-202, Sequencer – Blower Motor 2 Circuit, Delay On

Morris, THDR-202, Sequencer – Blower Motor 2 Circuit, Delay On – 30-70 sec, Off – 1-40, DPST NO Features: Sequencers are used in electric heat systems to stage blower motors and heating elements 24 volt

Morris TWG840586, Direct Drive Furnace Blower Motor, 1/3 HP

Morris, TWG840586, Direct Drive Furnace Blower Motor, 1/3 HP, 208/230V, 1075/3 Speed Features: Ball bearings now standard Installs with all Standard 48 frame mounting brackets Standard shaft length, diameter, and flats Uses 370V Capacitors 2.5in Diameter Hub Rings included Drain holes with plugs in booth end plates Automatic thermal overload protector Standard 48 frame motor

Morris THDR-222, Sequencer – Blower Motor 4 Circuit Staged 2 DPST NO

Features: Sequencers are used in electric heat systems to stage blower motors and heating elements 24 volt

Morris THSK1, Hard Start Kit, 3.5 – 5 HP

Features: Diversitech hard start kits reduce contactor call backs by boosting the startingcapacitor for a compressor Prevents home brownouts and improves homeowner satisfaction Diversitech’s hard starting kit feature a potential relay that disconnects the start capacitor from the circuit at exactly the moment it is no longer needed to boost the compressor – This results

Morris TIGN-001, Universal Silicon Carbide Igniter

Features: Silicon Carbide Igniter TrueStart hot surface igniters are 100% tested and completely reliable They are compatible with all OEM furnaces TrueStart hot surface igniters are available as a universal silicon carbide igniter CSA Listed

Morris TIGN-1R, Hot Surface Igniter, Round, Silicon Nitride

Features: Round Silicon Nitride TrueStart hot surface igniters are 100% tested and completely reliable They are compatible with all OEM furnaces TrueStart hot surfaces igniters are available as direct replacement for OEM(silicone carbide) or as a universal igniters allow a contractor to reduce truck stock and replace hundreds of OEM igniters with just one SKU

Morris TIGN-409, True Start Hot Surface Igniter 0.92″ Pin

True Start Hot Surface Igniter 0.92″ Pin

Morris TMG-1, Manifold Gauge and Hose Set

Features: Diagnostic and monitoring analog gauge set complete with hoses Details gauge readings in PSI degF The manifold gauge and Hose Set includes: 2 valve brass manifold 5ft long high pressure hose set For use with the following refrigerants: R-410A R-22 R-407C

Morris TPF-KIT, HVAC Flushing Solvent Kit, 8oz

Features: A flushing solvent for A/C and refrigeration systems Formulated for R410A retrofits, refrigerant conversions and compressor burnouts Compatible with all refrigerants and compressor oils All solvents in Pro-Flush are non VOC and comform to EPA SNAP standards: low toxicity and residue free Available as a kit or 16 oz. solvent refill The kit makes

Morris TT2401, Class 2 Transformer, Open Core, 40VA, 120 – 24V

Features: Power source for heating, air conditioning or refrigeration systems Class 2 UL Recognized

Morris TT2404, Class 2 Transformer, Open Core, 40VA, 120/208/240 – 24V

Features: Power source for heating, air conditioning or refrigeration systems Class 2 UL Recognized

Morris TT3401, Class 2 Transformer, Multi-Mount, 40VA, 120 – 24V

Features: Power source for heating, air conditioning or refrigeration systems These are multi mounted Wire connection secondary Class 2 UL Recognized

Morris TT3403, Class 2 Transformer, Multi-Mount, 40VA

Morris, TT3403, Class 2 Transformer, Multi-Mount, 40VA, 120/208/240 – 24 V Features: Power source for heating, air conditioning or refrigeration systems These are multi mounted Wire connection secondary Class 2 UL Recognized

Morris TTRIPLE-D, Universal Coil Cleaner, 1 Gal

Features: Universal coil cleaner that can be used on condensers, evaporators, microchannels, roof-top units, and mini-split applications Triple active synergistic highly effective solution is formulated to remove a broad range of soils while degreasing and deodorizing Ideal for cleaning most metals including aluminum and copper while extending equipment life and diminishing the potential for refrigerant

Morris TWG840467, Direct Drive Furnace Blower Motor

Morris, TWG840467, Direct Drive Furnace Blower Motor, 1/2 – 1/6 HP, 208-230V, 1075/4 Speed Features: Ball bearings now standard Multi-Horsepower motors are specially designed to cover a range of applications The blower motors horsepower ranges from 1/2 to 1/6 HP 1075 rpm Motor horsepower range from 1/2 to 1/6 in 208/230 volts all at 1075